![]() # Beware that on some FTP servers, ASCII support allows a denial of service Turn on the below options to have the server actually do ASCII # By default the server will pretend to allow ASCII mode but in fact ignore # however, may confuse older FTP clients. # recommended for security (the code is non-trivial). # Enable this and the server will recognise asynchronous ABOR requests. # ftp server can use as a totally isolated and unprivileged user. # It is recommended that you define on your system a unique user which the # You may change the default value for timing out a data connection. # You may change the default value for timing out an idle session. # Note that the default log file location is /var/log/xferlog in this case. # If you want, you can have your log file in standard ftpd xferlog format. # You may override where the log file goes if you like. Note! Using "root" for uploaded files is not # If you want, you can arrange for uploaded anonymous files to be owned by # Make sure PORT transfer connections originate from port 20 (ftp-data). # times returned by the MDTM FTP command are also affected by this # If enabled, vsftpd will display directory listings with the time # Activate directory messages - messages given to remote users when they # Uncomment this if you want the anonymous FTP user to be able to create # obviously need to create a directory writable by the FTP user. # has an effect if the above global write enable is activated. # Uncomment this to allow the anonymous FTP user to upload files. # if your users expect that (022 is used by most other ftpd's) # Uncomment this to enable any form of FTP write command. # Uncomment this to allow local users to log in. # Allow anonymous FTP? (Disabled by default) This parameter and the listen parameter are mutually # Like the listen parameter, except vsftpd will listen on an IPv6 socket # Run standalone? vsftpd can run either from an inetd or as a standalone # Please read the nf.5 manual page to get a full idea of vsftpd's # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please see nf.5 for all compiled in defaults. # loosens things up a bit, to make the ftp daemon more usable. # The default compiled in settings are fairly paranoid. Whenever I try and login via filezilla i get: Connection attempt failed with "ECONNREFUSED - Connection refused by server".Īnyone have any ideas on what is wrong? # Example config file /etc/nf I've created a user (drupal-ftp) with a matching folder under /home/ this is the user I attempt to login with.ĭrwxrwxrwx 2 drupal-ftp drupal-ftp 4096 Jun 27 20:12 drupal-ftp No, SFTP will not work for my application nor anything requiring a key pair. Those last two groups were for guides trying to get passive mode going. I've run through a few guides and still nothing is allowing me to gain access over port 21. MasqueradeAddress 52.77.215.I'm trying to get FTP access to my EC2 instance. added below two lines, 52.77.215.251 is the server public address. Using server address instead.", needs to set to support the passive mode, as the ftp is behind the NAT. Tcp6 0 0 :::21 :::* LISTEN 7839/proftpd: create user account to access the ftp,ģ, proftp configuration, "emacs /opt/lampp/etc/nf", add below lines, to make the folder /home/huilin to be accessible by ftp,Ĥ, passive mode error "Status: Server sent passive reply with unroutable address. Installed the Lampp, last time I was using vsftpd as ftp service, this time in Ubuntu, I use the proftpd which comes with the LAMPP package as ftp service, below is the procedure to setup, I started a new AWS ec2 instance, it is "Ubuntu Server 14.04 LTS (HVM), SSD Volume Type", note down a few points here,ġ, use the same key pair to access to the AWS EC2 instance, as import the private key file into the putty and WinSCP.Ģ, stop and start your instance in the AWS console panel, the AWS will assign a new public DNS and IP to your ec2 instance, my new Ubuntu public ip address is 52.77.215.251.Ĥ, Default ssh Usernames For Connecting To EC2 Instances, refer to this Link, Ubuntu username is 'ubuntu', RHEL username is 'ec2-user'.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |